modog
New Member
Posts: 8 
|
Post by modog on Jun 11, 2017 2:22:23 GMT
Just found this blog never done one so please forgive my ignorance I've had my 7100 for about two years and the other day one blade quit turning I checked to make sure it was pluged in then tried again still not working then other side quit and had a burning electrical smell found this site checked the 100 amp fuses one was blown having to order since no one had ever seen one here at boat shop and even tried a golf cart shop any ways emailed raven and tried called got the auto email reply never got an answer at their number I hope this fuse fixes it but smell concerns me I've learned a lot from what I've read here so thanks for the info If anyone has an idea on something else I might check after I replace the fuse checked the other fuse beside it and it is good I love the Raven but concerned if the company is going to be around for parts later.
|
|
|
|
Post by crawford on Jun 11, 2017 19:48:07 GMT
try calling early morning before 10 AM
|
|
modog
New Member
Posts: 8
|
Post by modog on Jun 13, 2017 23:41:25 GMT
Ok finally got a fuse by UPS today installed it started mower pulled up button nothing happened so I put in reverse to back out won't move in gas or electric checked that fuse is blown will this effect the blades from turning I'm going to call raven in the morning I hope they answer any suggestions in case they don't
|
|
|
|
Post by crawford on Jun 14, 2017 18:03:40 GMT
I found that if 48 volt packs weren't charged mine wouldn't move either. If you have a charger charge it till light is green
|
|
modog
New Member
Posts: 8
|
Post by modog on Jun 14, 2017 19:06:10 GMT
Battery is charged got through to Raven this morning very nice guy think francisco said he would send out controller and fuses ask about the business said not closing making generators but not the raven any longer called at 950am got right through you were right about when to call he said if the main fuse was blown it wouldn't move like you said call before 10
|
|
james
New Member
Posts: 1
|
Post by james on Aug 2, 2017 17:28:50 GMT
I can't get the blades to work
|
|
denny
Junior Member
Posts: 99
|
Post by denny on Aug 3, 2017 15:06:53 GMT
Not much info to go on James.
Has it been working ok?
Is transmission in low gear?
Is generator switch to off?
Red plug in cord good and tight?
Everything normal otherwise?
|
|
|
|
Post by crawford on Aug 3, 2017 17:31:44 GMT
denny check your pressure switch under seat
|
|
modog
New Member
Posts: 8
|
Post by modog on Aug 4, 2017 2:09:11 GMT
Raven service tech came to house today to check out my unit, left mower blade still not working after they sent me 2 new controllers after I installed them the left still wouldn't work also when I shut off the blades the engine would shut off but start right back up also was slow on engaging forward or reverse so tech replaced all the major components all the electronic boxes, battery pack although battery checked ok will still not move but if you switch to battery only and push pedal it will move about a foot then stop has them stumped supposed to call me back Monday with options might can return to lowes where I purchased it. I really hope they can figure it out cause I really like it when it's working I live in east tn and they are coming over here they came over a little over a week after I spoke to them I did find out if you don't have a service center near you if you can find a shop that will work on them they will pay the shop for warranty work after they've approved them golf cart shops might be a good source worth checking into if your a long ways from charlotte nc he didn't look at the mower deck wouldn't matter if unit won't go I'll let you know what happens next
|
|
